Skip to content
CALL TODAY phone number 561.229.1418
CALL TODAY phone number 561.229.1418

PSI Arizona A-11/R-17 (CR-17) Steel and Aluminum Erection (Commercial)/(Residential) Certification Package

$1,252.48

To be certified The Arizona Business Management exam must be taken as well. 

SCOPE OF WORK
A-11 Steel and Aluminum Erection - Field fabrication, erection, repair, and alteration of architectural and structural steel and aluminum materials common to the industry, including field layout, cutting, assembly and erection by welding, bolting, wire typing or riveting.

R-17 Structural Steel and Aluminum - Installation and repair of architectural and structural shapes and members common to the industry, including reinforcing steel that may be used as structural members for buildings, equipment, and structures. This scope includes all R-17R subclassifications. Steel Floor, Sub Floor and Form Systems, Welding, Ornamental Metals, Tanks, Recreational Equipment, Rebar, Post Tensioning and Wire Mesh.

The exam is 50 questions taken over 120 minutes. The required minimum passing score is 70% which means 35 questions need to be answered correctly to pass.

The trade test is considered equivalent for these classifications and upon passing the and trade exam, either license classification may be applied for without further testing.

The reference material listed above was used to prepare the questions for this examination. The examination may also contain questions based on trade knowledge or general industry practices. Except for Code books, you can base your answers on later editions of references as they become available. For Code questions, the examinations will be based only on the edition of the Code book that is listed. Candidates may use a silent, nonprinting, non-programmable calculator in the examination center

The first book may be brought into the exam center, but the others may not. 

The following reference material is allowed in the examination center

Code of Federal Regulations - 29 CFR Part 1926 (OSHA

The following reference material is not allowed in the examination center:

ASME B30.5 - Mobile and Locomotive Cranes, 2007

Handbook of Rigging, 5th Edition, 2009

Modern Welding, 2004,

Principles and Practices of Commercial Construction, 2008, 8th Edition,

Handling and Erection of Steel Joists and Joist Girders, 2006 edition

SDI (Steel Deck Institute) Manual of Construction with Steel Deck, 2006, 2nd Edition

Specification for Structural Joints Using ASTM A325 or A490 Bolts, 2004

Candidates are responsible for bringing their own references to the examination center. Reference materials may be highlighted, underlined, annotated and/or indexed prior to the examination session. However, references may not be written in during the examination session. Any candidate caught writing, highlighting, underlining and/or indexing in the references during the examination will be reported to the Arizona Registrar of Contractors. Furthermore, candidates are not permitted to bring in any additional papers (loose or attached) with their approved references. References may be tabbed/indexed with permanent tabs only. (permanent tabs are defined as tabs that would tear the page if removed). Temporary tabs, (defined as Post-It notes, or other tabs that may be removed without tearing the page) are not allowed and must be removed from the reference before the exam will begin. If you are downloading from the Internet, you may bring this reference into the testing center with you as long as it is bound. You can have it spiral bound or you may hole-punch it and put it in a binder. 

|title=Mandatory Business Exam|psi-arizona-buisness-management-exam-certification-package|title=Reference Materials|osha-construction-standards-regulations-29-cfr-1926|mobile-and-locomotive-cranes|handbook-of-rigging-for-construction-and-industrial-operations-mechanical-engineering-5th-edition|modern-welding-11th-edition|principles-practices-of-commercial-construction-9th-edition|technical-digest-no-9-handling-and-erection-of-steel-joists-and-joist-girders|sdi-manual-of-construction-with-steel-deck|specification-for-structural-joints-using-astm-a325-or-a490-bolts|title=Application Service|application-service|
Uptryve Systems Uptryve Systems